HP Thermal Shutdown issue?

What are the effective steps to resolve the HP Thermal Shutdown issue?

HP Thermal Shutdown is one of the major technical issues that bother many HP users. Whenever the message ‘Thermal Shutdown Occurred’ gets displayed, it creates a panic among them.

So, what is HP Thermal Shutdown? It is basically a thermal shutdown functionality in an HP device. It refers to a circuit that averts deterioration and breakdown because of a greater ambient temperature and the device’s heat generation. This malfunction occurs due to a big current load. This shutdown mainly occurs when the temperature of a central processing unit or a system goes to a critical level. At this juncture, the system shuts down automatically. It occurs to prevent complete damage to the device.

There are many causes for the HP Thermal Shutdown problem. There are many factors that result in the system overheating. There are several users who are unable to fix this issue. This problem can be intricate and demands an expert’s advice and support. In a few cases, you might have to replace some components of your system.

Main Reasons for HP Thermal Shutdown Issues

The problem of HP Thermal Shutdown in an HP laptop or notebook generally occurs when its CPU temperature hits a peak level. If overheating happens then it negatively impacts your device’s applications and processing speed. As a result, these components slow down and eventually shuts down. This technical malfunction annoys every user and slows down their work. So, it should be fixed instantly. There are several internal and external factors that are responsible for this situation. Therefore, it’s highly advisable to contact any reliable service provider to fix this issue for you.

In the below-listed points, we are listing out the main reasons for HP Thermal Shutdown Issues.

  1. There might be any misconfigured power settings in your system
  2. Your operating system is burdened with a heavy load
  3. Your system configuration is outdated
  4. There might be a defective air fan in an unnoticed state
  5. Lack of proper ventilation
  6. Installation of multiple third-party applications
  7. Incompatible device drivers
  8. Blockage of Air leads to excessive heating up of HP device

Troubleshoot Fixes for the HP Thermal Shutdown Issue

We will now discuss the troubleshooting fixes for the HP Thermal Shutdown issue.

  1. Keep your HP device off for a few minutes

Whenever this error occurs, you are advised to keep your HP device off for a few minutes. There are some parts in your HP laptops that demand a cooldown period of about 10 to 15 minutes. This time completely depends on your room’s temperature. You should not be in a hurry to switch off your HP device. Therefore, you are requested not to put your HP device in a refrigerated location. It is because the sudden reduction in temperature will severely damage the internal components of your HP device.

  • Checking out for any Physical Damage

You should take away the power cable of your HP laptop. You should use a screwdriver to open the side door of your device. After opening it, should properly check whether there is any physical damage inside it or not. In this process, you can also use a small flashlight for this purpose. If you find any dirt or debris in the case or surrounding then you should clean it immediately. It should be cleaned as it works as an insulator. You should take a clean cloth and then wipe away all the dust.

  • Attaching the power again

If everything looks fine then you should re-attach the power cable. While doing so, you should make sure to close the case door.

4. Performing a Quick Check of the Failure

It’s time to quickly scan for any technical failure. Now, the case of your HP laptop should be open. Next, you should switch on your HP laptop and then inspect the system and CPU fans closely. They should be spinning appropriately. If not, then you should check whether their connectors are loose or damaged.

  • Re-installing the Heat Sink

In a few cases of HP thermal shutdown cases, the thermal paste between the heat sink and CPU gets contaminated. It leads to the overheating of your HP device. Therefore, it’s necessary to remove and then install the heat sink again.

Additional Procedures to Fix HP Thermal Shutdown Issues

If you are unable to fix the thermal shutdown problem, then you should try isolating the issue to fix it. For doing so, you are advised to perform a hard reset and configure BIOS default and then restart.

  1. Performing a hard reset

For performing a hard reset, you should follow the below-mentioned steps: -.

  1. Firstly, you should shut down your HP device
  2. Now, you should take off the adaptor and other connected peripherals.
  3. Next, you should remove the battery but don’t take away the built-in computer battery
  4. Thereafter, you should hold and press your HP device’s power button for around 20 seconds
  5. Now, you should plug back the adaptor and the battery into your HP device
  6. Finally, you should switch on your HP device and check whether the problem is resolved or not.
  • Configuring BIOSS and restarting

To set BIOS default, you are advised to restart your HP notebook. Thereafter, you should follow the below-mentioned instructions.

  1. First of all, you should keep pressing F10 till you find the BIOS menu displaying.
  2. Now, you should hit F9 after you see the BIOS menu displaying.
  3. Next, you should choose ‘Yes.’
  4. Thereafter, you should hit F10 to save the modifications.
  5. Finally, you should ‘Yes’ to confirm. Thereafter, your computer will be restarted in the default settings.

Conclusion

HP Thermal Shutdown issues can be complicated and severe to your devices and should be fixed properly. We have detailed the main reasons and troubleshooting fixes to resolve this issue perfectly. If you require any technical help or assistance then you can contact our technical support team.

0 0 votes
Article Rating
Subscribe
Notify of
guest
0 Comments
Inline Feedbacks
View all comments
0
Would love your thoughts, please comment.x
()
x